State¶

The state of the socket. The state can be one of these values:

INIT

The SMC socket is being initialized. It is not connected nor listening yet.

CLOSED

The SMC socket is closed. It is not connected nor listening anymore.

LISTEN

The SMC socket is a listening socket, waiting for incoming connection requests.

ACTIVE

The SMC socket has an established connection. In this state, the TCP connection is fully established, rendezvous processing has been completed, and SMC peers can exchange data via RDMA.

PEERCLW1

No further data will be sent to the peer.

PEERCLW2

No further data will be sent to or received from the peer.

APPLCLW1

No further data will be received from the peer.

APPLCLW2

No further data will be received from or sent to the peer.

APPLFINCLW

The peer has closed the socket.

PEERFINCLW

The socket is closed locally.

PEERABORTW

The socket was abnormally closed locally.

PROCESSABORT

The peer has closed the socket abnormally.

UID¶

User ID of the SMC socket.

Inode¶

Inode attribute of the socket.

Local Address¶

Address and port number of the local end of the SMC socket. The displayed address is truncated when it ends with '..'. -W, --wide can be used to display addresses untruncated.

Peer Address¶

Address and port number of the remote end of the socket. Analogous to "Local Address".

Intf¶

When the socket is explicitly bound with setsockopt option SO_BINDTODEVICE then Intf shows the interface number of the Ethernet device to which the socket is bound.

Mode¶

SMCD

The SMC socket uses SMC-D for data exchange.

SMCR

The SMC socket uses SMC-R for data exchange.

TCP

The SMC socket uses the TCP protocol for data exchange, because an SMC connection could not be established.

In case of an error during connection setup, respective error codes will be displayed in the format <local>/<remote>.

Linux error codes:

0x01010000

Out of memory

0x02010000

Timeout while waiting for confirm link message over RDMA device

0x02020000

Timeout while waiting for RDMA device to be added

0x03000000

Configuration error

0x03010000

Peer does not support SMC

0x03020000

Connection uses IPsec

0x03030000

No SMC devices found (R and D)

0x03030001

No ISM device for SMC-D found

0x03030002

No RDMA device for SMC-R found

0x03030003

Hardware has no ISMv2 support

0x03030004

Peer sent no SMCv2 extension

0x03030005

Peer sent no SMC-Dv2 extension

0x03030006

Peer sent no ISMv2 SEID

0x03030007

No SMC-Dv2 device found, but required

0x03030008

Peer sent no UEID

0x03040000

SMC modes mismatch (R or D)

0x03050000

Peer has eyecatcher in RMBE

0x03060000

Fastopen sockopt not supported

0x03070000

IP prefix / subnet mismatch

0x03080000

Error retrieving VLAN ID of IP device

0x03090000

Error while registering VLAN ID on ISM device

0x030a0000

No active SMC-R link in link group

0x030b0000

SMC-R link from server not found

0x030c0000

SMC version mismatch

0x030d0000

SMC-D connection limit reached

0x030e0000

SMC-Rv2 connection found no route to peer

0x030f0000

SMC-Rv2 connection mismatch direct/indirect with peer 0x04000000 Synchronization error

0x05000000

Peer declined during handshake

0x09990000

Internal error

0x09990001

rtoken handling failed

0x09990002

RDMA link failed

0x09990003

RMB registration failed

ShutD¶

<->

The SMC socket has not been shut down.

R->

The SMC socket is shut down one-way and cannot receive data.

<-W

The SMC socket is shut down one-way and cannot send data.

R-W

The SMC socket is shut down in both ways and cannot receive or send data.

Token¶

Unique ID of the SMC socket connection.

Sndbuf¶

Size of the to-be-sent window of the SMC socket connection.

Rcvbuf¶

Size of the receiving window of the SMC socket connection (filled by peer).

Peerbuf¶

Size of the peer receiving window of the SMC socket connection (to fill during RDMA-transfer).

rxprod-Cursor¶

Describes the current cursor location of the "Rcvbuf" for data to be received from the peer.

rxcons-Cursor¶

Describes the current cursor location of the "Peerbuf" for data sent to peer and confirmed by the peer.

rxFlags¶

SMC socket connection flags set by and received from the peer.

txprod-Cursor¶

Describes the current cursor location of the "Peerbuf" for data sent to peer.

txcons-Cursor¶

Describes the current cursor location of the "Rcvbuf" for data received from the peer and confirmed to the peer.

txFlags¶

SMC socket connection flags set locally and sent to the peer.

txprep-Cursor¶

Describes the current cursor location of the "Sndbuf" for data to be sent. The data is to be moved to the "Peerbuf".

txsent-Cursor¶

Describes the current cursor location of the "Sndbuf" for data sent. The data was moved to the "Peerbuf".

txfin-Cursor¶

Describes the current cursor location of the "Sndbuf" for data sent and send completion confirmed. The data was moved to the "Peerbuf" and completion was confirmed.

Role¶

CLNT

The link group of the SMC socket is used for client connections.

SERV

The link group of the SMC socket is used for server connections.

IB-Device¶

Name of the RoCE device used by the link group to which the SMC socket belongs.

Port¶

Port of the RoCE device used by the link group to which the SMC socket belongs.

Linkid¶

Unique link ID of the link within the link group to which the SMC socket belongs.

GID¶

Gid of the RoCE port used by the link group to which the SMC socket belongs.

Peer-GID¶

Gid of the Foreign RoCE port used by the link group to which the SMC socket belongs.

VLAN¶

tbd.